USB audio interface · 2011
eBox-44
A bus-powered four-in, four-out audio interface small enough to live in a laptop bag. Built-in phono preamps and a ground post meant it could take turntables directly — which made it a natural fit for timecode DJs and for digitising vinyl.
At a glance
- Type USB bus-powered audio interface, 4 in / 4 out
- Inputs 4 × RCA, switchable line or phono (built-in phono preamps and ground post); 1 × ¼″ microphone input with gain control
- Outputs 4 × RCA; 1 × ¼″ headphone output with level control
- Metering Blue signal-present LEDs on all four inputs and all four outputs, plus a phono-mode LED
- Sample rates 44.1 kHz and 48 kHz, 16 bit
- Drivers Low-latency ASIO on Windows, Core Audio on macOS
- Power USB, 5 V / 500 mA — no external supply
- Dimensions 118.9 × 125 × 46.5 mm (4.7 × 5 × 1.8 in)
- Weight 385 g (13 oz)
- In the box eBox-44, USB cable, two RCA cables, installation CD, manual
Connections
- Inputs 1–4 — RCA. Line and phono level devices are both supported.
- Phono / Line switch — set to
PHwhen turntables are connected to inputs 1–4, andLNfor everything else. The phono LED confirms phono mode. - Ground post — connect your turntable's ground cable here.
- Outputs 1–4 — RCA to your mixer's inputs. Routing is set in your software.
- Microphone input and volume — ¼″ jack with its own gain control.
- Headphone jack and volume — for monitoring inputs while recording.
- USB port — data and power, over the supplied cable.
Audio specifications
Line outputs
| Load | 47 kΩ |
|---|---|
| Output level | 2 Vrms, +1 / −0.5 dB |
| THD | ≤ 0.01 % |
| Frequency response | 20 Hz – 20 kHz, ±1 dB |
| Signal to noise | Better than 93 dB |
| Channel separation | Better than 90 dB |
Headphone output
| Load | 32 Ω |
|---|---|
| Output level | 1.7 Vrms ±1 dB (85 mW per channel) |
| THD | ≤ 0.01 % |
| Frequency response | 20 Hz – 20 kHz, ±1 dB |
| Signal to noise | Better than 90 dB |
| Channel separation | Better than 72 dB |
Line inputs
| Impedance & sensitivity | 10–50 kΩ, −14 dBV (200 mV) ±2 dB |
|---|---|
| Frequency response | 20 Hz – 20 kHz, ±2 dB |
| THD + N | ≤ 0.025 % |
| Signal to noise | Better than 80 dB |
| Channel separation | Better than 75 dB |
| Maximum input | Better than +7 dB |
Phono inputs
| Impedance & sensitivity | 47 kΩ / 100 pF, −54 dBV (2 mV) ±2 dB |
|---|---|
| Frequency response | 20 Hz – 20 kHz, ±2 dB |
| THD + N | ≤ 0.1 % |
| Signal to noise | Better than 78 dB |
| Channel separation | Better than 75 dB |
| Maximum input | Better than −32 dBV |
Microphone input
| Impedance & sensitivity | 2.2 kΩ, −54 dBV (2 mV) ±2 dB |
|---|---|
| Frequency response | 20 Hz – 20 kHz, ±2 dB |
| THD + N | ≤ 0.1 % |
| Signal to noise | Better than 80 dB |
| Maximum input | Better than −32 dBV |
Driver compatibility. The macOS v3.0.0 and Windows
v2.9.53 drivers below are the final releases and were built for
operating systems of that era — the manual lists Windows 98SE through
Windows 7, and Mac OS X 10.3 or higher. They are unsigned by modern
standards and are not expected to load on current macOS releases. They
are preserved here for anyone running period-appropriate hardware.
eBox-44 downloads
Everything below is also on the full downloads page.
Documentation
Drivers
These are the final drivers Electrix shipped. They predate current operating systems — see the FAQ before installing on a modern machine.